Electrician in San Anselmo, CA
Max Electric provides electrical repairs and installation for San Anselmo homes, shops and offices. Bring us the fault you need resolved or the room you want to change. We can assess the existing circuits and plan lighting, outlets and appliance connections around how the space will be used.
On this page
Match the first visit to the work you need
| Your starting point | Useful information to share | What we need to establish |
|---|---|---|
| A circuit stopped working | Affected rooms, when it began and equipment running at the time | The cause, safe repair scope and whether other circuits are involved. |
| A replacement appliance | Make, model and intended location | Supply requirements and whether the existing connection is suitable. |
| A kitchen or bathroom remodel | Layout, fixtures, appliance schedule and construction timing | Device locations, circuit changes and when wiring must remain accessible. |
| Charging in the garage | Parking position, vehicle use and charger choice if known | Practical cable reach, available capacity and the wiring route. |
| A shop or office alteration | Equipment layout, operating hours and property contact | Access, load requirements and an agreed interruption plan. |
No need to diagnose the problem before calling. A clear description is enough to begin; photographs can help when they can be taken safely without opening equipment.
Electrical service for the immediate problem and the next project
Repairs that start with diagnosis
A dead outlet or recurring trip can have more than one cause. We examine the affected installation, explain the findings and distinguish the immediate repair from optional improvements.
Troubleshooting and repairs →Dedicated appliance circuits
An induction range, dryer or other appliance needs a connection matched to its actual specifications. We review the circuit, protective device and route rather than treating a nearby receptacle as proof the supply is suitable.
Appliance circuit installation →Remodel and ADU electrical work
We coordinate wiring with the room layout, equipment schedule and building work. Early decisions about controls and connections help prevent late changes after cabinetry or finishes are installed.
Remodel and ADU services →Panel and service planning
A panel review considers equipment condition and the loads you plan to add. We explain whether the work is a panel replacement, a distribution change or a service project involving the utility.
Panel upgrade assessment →Garage and driveway charging
We plan a charger around the parking space, charging needs and available supply. Share plans for other electric appliances too, so the capacity decision does not address the car in isolation.
EV charger installation →A room remodel has electrical decisions at each stage
Keeping the same cabinet layout does not necessarily mean keeping every circuit or connection unchanged. Resolve the electrical details alongside the room design.
Before products are ordered
Compare the proposed appliances and fixtures with the existing supply. A change from one type of cooking equipment to another may affect the circuit and capacity plan. Choose the actual models or provide their specifications before treating the electrical allowance as final.
Before rough wiring
Set outlet and switch locations against the cabinet drawings, doors and work surfaces. Identify lighting groups and controls. The electrician and builder need to agree on access and on any wiring that must remain visible for inspection.
Before the room is closed
Confirm that changes to the layout have reached everyone doing the work. A moved island or appliance can alter an electrical route. Required inspections and any corrections should be resolved before the relevant work is concealed.
At finish installation
Fit the selected devices and controls, test the completed work and walk through operation with the owner. Keep product information and relevant inspection records. If an item is deferred, record what remains rather than treating the whole room as complete.
Lighting should suit the way the room is used
General ceiling light may not put light where you prepare food, read or work. We can discuss task lighting and control locations with your room plan. A modest change to switching can be more useful than adding fixtures without considering where people stand or sit.
For retained fixtures, tell us about flicker, buzzing or a dimming range that no longer works well. We check the relevant lamp, driver and control compatibility as part of the investigation. The remedy depends on the equipment; it is not always a new circuit or a replacement for every fixture.
Use San Anselmo’s permit process for the actual scope
The Town of San Anselmo directs building permit applications through its eTRAKiT portal and publishes separate guidance for in-kind kitchen and bathroom remodels. That distinction is useful when defining a project: retaining a layout and changing it are not necessarily the same submission.
We review the electrical scope with the relevant town requirements and the larger construction plan, where there is one. Do not assume that an appliance swap or a room described as cosmetic settles every permit question. If the service connection changes, utility coordination also needs to be included in the schedule.
Repairs and alterations in a working business
A small electrical change can affect more than the room where it takes place. Tell us how the premises operate before the visit.
For a shop, office or service business
Identify the equipment that loses power during the proposed work and the person responsible for restarting it. A tenant may control the room while the owner controls the service equipment. We need access and authorization from the right parties, not simply an empty appointment slot.
For an occupied rental or shared building
Confirm which unit or common area is affected and whether any circuits serve more than one space. Occupant notification, service-room keys and clear access can determine when work proceeds. We help define the electrical scope and coordinate it with the manager’s responsibilities.
A useful estimate describes the work, not just the total
What stays and what changes
Look for the affected equipment, circuits and rooms. If the project includes optional improvements, they should be distinguishable from repairs needed to complete the agreed scope.
How the wiring gets there
Compare route assumptions and any likely openings. Confirm responsibility for wall repairs, painting, trenching or other surrounding work where applicable.
What depends on someone else
Town review, utility work, equipment delivery and other trades can affect installation timing. Ask which dates depend on town review, utility work or other trades.
Questions about hiring an electrician in San Anselmo
Can you handle a small electrical repair in San Anselmo?
Yes. Describe the affected device or circuit and when the problem occurs. We can assess a limited repair without assuming it requires a remodel or a complete panel replacement. If the diagnosis identifies a broader issue, we explain why it matters and what work it affects.
Do I need electrical work if my new kitchen uses the same layout?
Possibly. New appliances, lighting or controls may have different requirements even when their locations stay the same. Share the product specifications and layout so we can check the existing supply and connections. The town also publishes guidance specifically for in-kind kitchen and bath remodels.
Can you coordinate with the cabinet installer?
Yes. Final cabinet drawings help establish practical outlet, lighting and appliance-connection locations. Let us know the installation sequence and who can approve layout changes. Electrical rough-in and applicable inspections need to fit that sequence before access is closed.
What if I am not ready to choose a charger yet?
We can discuss likely parking and wiring routes and review the broader electrical plan. Final circuit design still depends on the charger and intended output. Any preparation should be described accurately; a reserved route or spare panel position is not a completed charging installation.
What are you changing in San Anselmo?
Send the address and describe the repair or renovation. Already chosen your appliances? Include their model numbers. Room plans and the date your builder expects to start are useful too.